Wood & steel frame
Wrought iron
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGate Company in Elmwood Park, NJ
Gate installation in Elmwood Park, NJ is mostly short swing gate work: a driveway gate hung between a house and a property line on a 40- to 50-foot lot, sized to clear the neighbor’s fence and the driveway apron without swinging over the sidewalk. We’re a gate-only company – repair, electric gate repair, and installation – so the crew that shows up works on gates every day, not on gates between other jobs. Whether you want a manual swing gate or a DoorKing or Ghost Controls operator behind it, we diagnose the site before we quote. Call (855) 701-9639 to set up a free on-site estimate.
Why Elmwood Park Homes Are Different
Elmwood Park is a densely built postwar suburb. Most single-family homes here sit on tight 40- to 50-foot lots, and the housing stock runs mostly to 1920s – 1950s frame and brick two- and three-bedroom homes, many with a detached or attached garage added later. That combination shapes gate work more than anything else. A replacement driveway gate usually has to be sized and hung to clear the neighbor’s fence on one side and the driveway apron on the other, and it must swing without crossing into the sidewalk. There’s rarely room to fudge the geometry.
The posts are the other issue. On these older properties, gate posts are often 4x4s set in aged concrete that has heaved or rotted, so a hardware swap won’t hold. Along the older blocks off Market Street and River Drive, plenty of driveway gates are original wrought-iron or chain-link units from the 1950s – 60s whose posts were set only 18 – 24 inches deep. They lean after a hard frost and need new footings, not just hinge adjustments. Add freeze-thaw winters that shift posts seasonally and humid summers that swell wooden gates until they drag on the latch side, and you get a town where re-hanging and re-setting are normal parts of the job. If a new gate or a power run is on your list, check with the borough about permits before anything gets dug or wired.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Our Main Elmwood Park Services
Gate installation and gate repair are what Elmwood Park homeowners call us about most, and both start the same way: we look at the opening, the posts, and the hardware before we quote anything.
Gate Repair in Elmwood Park
Most repairs here come down to the post or the hinge. Aged concrete under an old 4×4 lets the post shift with the frost, and a gate that drags, sags, or won’t latch is usually telling you the footing moved, not the hinge. We check the geometry first, then fix the real cause: re-set the post to proper footing depth, re-hang the gate, replace worn hinges and latches, and true up the frame. Summer humidity swells wooden gates until they bind on the latch side, which is a re-hang, not a shave. For sagging driveway gates on the older blocks, see Gate Repair in Elmwood Park.
Electric Gate Repair in Elmwood Park
Powered gates fail in two layers: the mechanical side and the electronics, and both have to be checked together. We diagnose the operator, the wiring, the safety edges, the photo eyes, and the limit settings, then test the gate under load before calling it fixed. Ghost Controls and DoorKing systems are common enough in this trade that we know their failure patterns well. One local note: frost heave that shifts a post will throw off a slide gate’s alignment and trip the safety reverse, so a “motor problem” is sometimes a footing problem. Details are on Electric Gate Repair in Elmwood Park.
Gate Installation in Elmwood Park
Most gate installation in Elmwood Park is replacement work on tight lots, and the lot lines decide the design before anything else does. On a 40- to 50-foot property, a driveway gate has to clear the neighbor’s fence and the driveway apron without swinging into the sidewalk, and the housing stock – 1920s – 1950s frame and brick homes with garages added later – means the posts usually need new footings rather than reuse. Freeze-thaw winters finish off anything set shallow. We measure the opening on site, size the gate to the swing it actually has, and set posts to proper footing depth. That’s the whole reason we do gate installation as a measured, scheduled job rather than a same-day fix.
Driveway Gate Installation
Signs you need it
Your driveway gate scrapes the sidewalk, won’t clear the neighbor’s fence, or the existing gate is an original 1950s – 60s wrought-iron or chain-link unit leaning on shallow posts.
What it costs in Elmwood Park
Most driveway gate installations here land in the range below, and the written estimate sets the final price once we’ve measured the swing and the footing conditions.
How we do it
We measure the opening and the apron, set new posts to proper footing depth, hang and true the gate, fit the hardware, and check the full swing against the fence and sidewalk line before we leave.
Automatic Gate Installation
Signs you need it
You’re tired of getting out of the car in the rain, or the gate is too heavy or too far from the house for anyone to reach comfortably by hand.
What it costs in Elmwood Park
Automation adds the operator, the power run, and the safety devices on top of the gate itself, so the figure sits in the range below and the written estimate confirms it.
How we do it
We match the operator to the gate’s weight and swing, run the power and control wiring safely, mount and align the operator, set the limits, and test the safety edges and photo eyes before handover.
What Gate Installation Costs in Elmwood Park
These are typical ranges, not a quote. The written estimate sets the final price.
| Item | Typical range in Elmwood Park |
|---|---|
| Driveway gate installation | $1,800 – $5,500 |
| Automatic gate installation | $3,500 – $9,000 |
| Sliding gate installation | $2,500 – $7,500 |
Can you install a gate on a tight Elmwood Park lot without it swinging into the sidewalk?
Yes. We measure the swing against the fence line and the driveway apron first, then size and hang the gate so it clears both without crossing the sidewalk. That measurement happens before we quote.
Do you handle the power run and the safety edges on an automatic gate?
Yes. Automatic gate work includes the power and control wiring, the operator alignment, and the safety edges and photo eyes. The on-site estimate confirms what your specific opening needs.
Brands We Service in Elmwood Park
We work on LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule systems, and we don’t claim parts we don’t have. Turnaround depends on the brand and the part, so the estimate tells you what to expect. See our brands for the full list.
See the difference
Before
After
Before
After
Before
AfterPricing for Gate Company in Elmwood Park, NJ
| Service | Typical range in Elmwood Park |
|---|---|
| Gate repair | $150 – $650 |
| Gate hinge and latch replacement | $120 – $350 |
| Gate post re-set or new footing | $250 – $900 |
| Gate re-hang or realignment | $150 – $500 |
| Electric gate repair | $200 – $800 |
| Gate operator repair | $250 – $900 |
| Safety edge and photo eye repair | $150 – $450 |
| Driveway gate installation | $1,800 – $5,500 |
| Automatic gate installation | $3,500 – $9,000 |
| Sliding gate installation | $2,500 – $7,500 |
In Elmwood Park, shallow or heaved footings push cost up because the post has to be dug out and re-set rather than adjusted, and automation adds the operator, the wiring, and the safety devices. You get the price in writing and agreed before any work starts, so the invoice matches the estimate.
Neighborhoods We Serve in Elmwood Park
We work across Elmwood Park, including the older blocks off Market Street and River Drive where the original wrought-iron and chain-link gates tend to sit on shallow posts, and the postwar streets around ZIP code 07407 where driveway gates are hung tight between house and fence. Tight lots and old footings are the two things that come up most. Dispatch runs from 7am to 7pm, Sunday through Friday, and we can often reach most Elmwood Park addresses the same day.
- Market Street area
- River Drive area
- Off Market Street blocks
- Off River Drive blocks
Service Area – Cities Near Elmwood Park
Elmwood Park sits close to several towns we also cover, and the same tight-lot and old-footing conditions show up across them. If you’re just outside the borough, we can still help: see our pages for Garfield, NJ, Lodi, NJ, Maywood, NJ, and Hackensack, NJ. Each one has its own page with local detail on how gates are typically built and repaired there. For anything spanning a property line between towns, a call sorts out the details.
Serving Elmwood Park, NJ – Our Local Coverage Area
We serve Elmwood Park and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
FAQs About Gate Company in Elmwood Park
Often the same day. We answer 24/7, and fast dispatch runs 7am to 7pm, Sunday through Friday. A call outside dispatch hours is booked into the next opening.
It depends on the gate and the power run. Most boroughs require a permit for a new gate and for electrical work, so check with Elmwood Park’s building department before digging or wiring. We can tell you what the job involves.
Yes, we cover Elmwood Park, including the blocks off Market Street and River Drive, and the nearby towns of Garfield, Lodi, Maywood, and Hackensack.
Ready to sort out your gate? Call (855) 701-9639 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday, closed Saturday. We’re gate-only specialists, our technicians have up to 15 years of experience, and we’ll diagnose before we quote so the price you agree to is the price you pay.
What happens when you call
- 1A real person answersNo phone trees. Talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3A background-checked tech heads outLicensed & insured, typically within 30-60 min.
- 4You approve before work beginsNothing starts until you say go.
What Elmwood Park Customers Say
"Hinge post had rotted at the base and the whole swing gate was sagging into the concrete. He rebuilt the post rather than talking us into a whole new gate, which two other companies had pushed for."
- Eduardo Ramirez"Reprogrammed every clicker in the HOA and set up the keypad codes. Patient with a very long list of residents."
- Kevin Vaughn"Solar panel on our remote gate wasn't keeping the battery up through the winter. He repositioned it, replaced the battery, and explained the math on why the old placement was never going to work."
- Rashad Robinson